Home > Dimmer Switch > Dimmer Switch Is Not Working

Dimmer Switch Is Not Working

Contents

Remember Me? most videos on this topic seem to show everything going smoothly. Just remember to SHUT OFF THE CIRCUIT BREAKER FIRST. Not the answer you're looking for? have a peek here

Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Good luck. Single-pole and three-way dimmer switches, like single-pole and three-way toggle switches, are used where lights are to be controlled from one or from two places. Time to upgrade your blinds? http://www.doityourself.com/forum/lighting-light-fixtures-ceiling-exhaust-fans/359655-dimmer-switch-not-working.html

Dimmer Switch Not Working Properly

Someone please help? For reference, this is the dimmer: http://www.lutron.com/Products/StandAloneControls/Dimmers-Switches/GlyderDimmer/Pages/Overview.aspx electrical lighting share|improve this question edited Aug 1 '11 at 21:30 Aarthi 85731829 asked Oct 8 '10 at 13:34 mohlsen 4,679122641 add a comment| The electrician found that the ceramic holder wire crimp did not hold and wires had touched.

  • Twist the ends together clockwise and cap them using a wire connector nut. • Connect the black dimmer wire to your tagged common wire and remove the electrical tape. • Connect
  • Dimming these lights requires pulsing the power so the light flashes at a faster rate, one that the brain does not detect, in order to produce less light, according to LEDs
  • There was a fault in one of the lines the first time I used it and the GFCI plug was thrown.
  • Login | FAQ + Reply to Thread Results 1 to 9 of 9 LinkBack LinkBack URL About LinkBacks Thread Tools Show Printable Version Search Thread Advanced Search Display Linear Mode
  • Early Out View Public Profile Visit Early Out's homepage!
  • Ultimate Handyman 49,330 views 6:26 How to Install a Dimmer Switch for Your Home Lighting System - Duration: 4:06.
  • You cannot test conductivity on a solid state dimmer with a VOM.

Oh, and uh, any special tools that don't come in the standard Do It Herself took kit that I'll need to pick up whilst at Home Depot? Sign in 9 9 Don't like this video? Full Answer > Filed Under: Electrical You May Also Like Q: Where can you find a wire gauge amp chart? Dimmer Switch Not Working With Led You will need a three-way dimmer and a three-way switch.

Share December 6, 2015 Finding the perfect lighting balance in every room of your home is as much an issue of function as it is of decor. Dimmer Switch Not Turning On Light Full Answer > Filed Under: Electrical Q: What are some different types of dimmer switches? AFter installation, the light is always on, turning the dimmer off, and moving the slider up and down, the light is always on. news If the light remains too bright with the dimmer, consumers should consider switching to other CFL and LED lamps that provide a warmer color to achieve the desired lighting levels.

Walch spent 40 years working in the electrical trades and holds an Associate of Applied Science in applied electrical engineering technology from Alvin Junior College. Dimmer Switch Does Not Work Could this have fried the dimmer? His work has appeared in “Family Handyman” magazine, “Popular Science,” "Popular Mechanics," “Handy” and other publications. You can only upload a photo or a video.

Dimmer Switch Not Turning On Light

So both of these (light always on and no conductivity) would tell me the dimmer is bad, but they are telling me opposite things. http://www.homedepot.com/c/how_to_install_a_dimmer_switch_in_fourty_five_minutes_video_HT_PG_EL Philster View Public Profile Find all posts by Philster #13 07-02-2003, 03:59 PM justwannano Guest Join Date: Jan 2000 Make sure the total wattage of your light bulb(s) Dimmer Switch Not Working Properly Shouldn't take more than about two minutes. Dimmer Switch Will Not Dim How to find x and y coordinates based on the given distance?

Three-Way Switch • If the house wires are bent, use a wire stripper to cut off the twisted ends. navigate here Besides black & white wires there is a grounding wire. Quite often, when a single dimmer switch is used to control a number of light fixtures, this maximum wattage is exceeded. Skip to main contenteBayShop by categoryEnter your search keywordAll CategoriesAdvancedHi (Sign in to bid or buy) Daily Deals Sell Help & Contact My eBayExpand My eBay Summary Bids/Offers Watch list Wish Dimmer Switch Not Working After Replacing Bulb

Any ideas, please ? Tighten a wire nut over each pair of wire ends. It took two replacements to figure that one out. Check This Out Incandescent and fluorescent dimmer switches are not interchangeable because dimmable fluorescent lights employ special ballast designed for that purpose.

One question....Does another switch also work the light you are dimming? Dimmer Switch Not Dimming Anymore after the switch, the line is always 120v, moving the dimmer and silding it the voltage remains at 120v. Everything Home TV 37,442 views 6:12 How to install Leviton Dimmer Switch - LevitonProducts.com - Duration: 7:41.

Watch Queue Queue __count__/__total__ Find out whyClose How to Fix a Broken Dimmer Switch in Your Home ehowhome SubscribeSubscribedUnsubscribe221,854221K Loading...

Reducing the current reduces the brightness of the light. View our Privacy Policy here. If the tester detects voltage, switch off the appropriate circuit breaker or remove the appropriate fuse and test the circuit again. • If you are replacing a three-way switch, one wire Dimmer Switch Only Turns On And Off Some yokel had replaced the 40 watt light bulbs with 60's.

Thanks everyone. A standard dimmer will not work: Quote: A dimming ballast must be installed to dim fluorescent lamps. current community blog chat Home Improvement Home Improvement Meta your communities Sign up or log in to customize your list. this contact form Source(s): Electrician since 1977 EagleWatcher · 6 years ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Asker's rating Report Abuse Dimmer Switch Not Working

Twist the ends together clockwise and cap them using a wire connector nut. • Connect each dimmer wire to a house wire by gripping the wire ends with a pair of Some even have warning about making sure not to change out bulbs with the power on. The Triac is probably shorted, and these are not made to have parts replaced. Louis, MO 50mi.

Charter Member Join Date: Jan 2003 Location: Richmond, VA Posts: 22,536 Installation is fairly straightforward, Sunshine.