Home > Dodge Ram > Dodge Ram Instrument Panel Not Working

Dodge Ram Instrument Panel Not Working

Contents

INSTRUMENT CLUSTER FAILURE MESSAGE Message Description Correction 110 A failure has been identified in the cluster CPU, RAM, or EEPROM. 1. Mark helpful 6,445 Report thejeepdoctor answered 3 years ago the bus originates in the inst. Obviously the mileage was mismatched but did you get any CEL or DTC codes or anything else funky? Thanks __________________ 2004 2WD 4.7QC, 6" Rough Country Lift 35x13.5 Pro Comps on 20s. http://sevevb.com/dodge-ram/dodge-4x4-not-working.html

Connect the battery negative cable. Any suggestions or thoughts on this?? If the wait-to-start indicator lamp does not illuminate during this test, the instrument cluster should be removed. Sign in to make your opinion count. https://www.cargurus.com/Cars/Discussion-t22033_ds560117

2004 Dodge Ram Instrument Cluster Problems

I wanted... 2001 Dodge Ram 1500 2 Dr SLT Quad Cab SB - Maintenance & Repair No buS on instrument panel it cranks but no gages work Electrical problem, Dashboard Panel The instrument cluster will perform a gauge actuator test. and Regional Chapters / Special Events Specialty Forums General Diesel Discussion Towing and Hauling / RV Fuels / BioDiesel / Diesel Prices Cummins Conversions Off Road / 4x4 Big Rigs Competition If OK, go to Step 6.

  1. I started out by chasing all the ground connections, checked the ECM ground, checked the PCM ground and all the grounds from both battery's.
  2. The truck uses a two wire communication system and if one of those wires goes out then the whole system is down.
  3. Whatever the problem...
  4. Since you have replaced the instrument cluster already then it is most likely due to a wiring problem.
  5. Must be a 3rd party that rebuilds the clusters.
  6. Check the CCD data bus connections at the cluster. 2.
  7. Published on Dec 1, 2012This is a quick video showing how to test the instrument cluster of your 98.5 to 2002 Dodge Cummins for problems or errors.
  8. This feature is not available right now.
  9. Check the CCD data bus bias. 3.
  10. Mark helpful 60 Report fuzesm answered 11 months ago https://www.facebook.com/xpkustomz/posts/991588000903053 6 out of 6 people think this is helpful.

I got a great mech here where i live and after 2 diff dealerships telling me buy a new cluster i knew someone was full of it. You can disconnect and reseat this plug to see if it clears it up. A series of three-digit numeric failure messages may appear in the odometer display, depending upon the failure mode. 2002 Dodge Ram 1500 Instrument Cluster Not Working I finished to test the instumental closter and it looks finei saw all gauges instruments been tested, all of them moved from one end to the other end and finally the

Continue to hold the reset button in for about 10 seconds until "CHEC" appears in the odometer display, then release the button. I can be driving down the road and it will cut out and all the gauges will die and I will get the "no bus" in the odometer like everyone else. Working... A 9Companion DTC9 was set in both the ECM and PCM. __________________ 01.5 2500 4X4 NV4500 5 speed 3:55, Airraid, 4" exhaust, Banks High-Ram, Adrenaline/Pulse, Mach 4's, Airdog 150, HTT62/71/14, 13"

Book time is .7hrs to exchange a cluster. 2006 Dodge Ram 1500 Instrument Cluster Problems I left the drivers side window down in the rain. Say faulty crank sensor they warranty and replaced said was fixed. If not OK, repair the open fused B(+) circuit to the fuse in the junction block as required.

Dodge Ram Instrument Cluster Reset

Begin with the key off and vehicle stopped.

John Greenough 100,183 views 5:06 2008 Dodge Ram 1500 Gauge LED Light Color Change (part 1 of 2) - Duration: 6:57. 2004 Dodge Ram Instrument Cluster Problems The 2015 F-150 - Duration: 13:11. 2003 Dodge Ram 1500 Instrument Cluster Problems i suggest very carefully to take out the circuit board and take it to one of those places were they fix computers and ask if they can take a look at

Connect the battery negative cable. http://sevevb.com/dodge-ram/dodge-ram-horn-not-working.html Can anybody help?Thanks in advance - Waterdoctor :confuse: 0 · Share on Facebook moparblue2 Posts: 86 August 2008 if it is not a newer Dodge controller. Good luck I hope it helps! It doesn't matter if you are driving, if the engine is on or off, these devices just randomly begin flashing together, then stop for a minute or two, and then begin Dodge Ram Instrument Cluster Codes

It all started with the truck would roll down the front windows by itself and one night it rained and got wet inside now I am having these problems Mark helpful This will test the cluster itself. The engine can run with the bus down. his comment is here I checked all the fuses (except for the two airbag ones) in the cab and none were problems.

As that will go to there inboxes on the watch list. Dodge Ram No Bus Fix A gentle 'rap' of a well placed closed fist on the top of the dash usually corrects the problem. Any info would be great, you can email me at [email protected] if you choose. 0 · Share on Facebook shawno69 Posts: 1 May 2008 I have a 2002 dodge ram quad

Truck runs completely normal.

everything worked fine the last time i drove it. Scotty Kilmer 352,623 views 3:41 Replacing Dodge Ram Door Speakers - Duration: 8:00. It turns over but dose not start. Dodge Ram Instrument Cluster Repair EdzGarage 192,889 views 7:35 Loading more suggestions...

little easier that way 0 · Share on Facebook KCRam Mt. Interesting... Wipers, headlights will not turn off all gauges not working, dash looks like a Xmas tree. weblink Best of luck and i hope i was somewhat helpful helpful bob · 9 years ago 1 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Report

If no failure message appears, the actuator test will proceed as described in Step 6. I was NOT HAPPY, but couldn't get Dodge to budge a bit on it. __________________ Maroon 2001 2500 QC 4x4 SB 3.55 6-speed 285/70R17 Cooper Discoverer ATP on 3rd gen rims, It's looks like a Christmas tree and the gauges are not working what would be the first step to checking this?!?!