Home > Not Working > Dimension One Spa Jets Not Working

Dimension One Spa Jets Not Working

Contents

You may find it easier to manipulate the jet adjustment while the pump is off, but should not be necessary. The jets aren't working! Repeat this process, using the lid like a plunger until water starts to come up at you from the filter housing. Any ideas? have a peek here

EVNautilus 3,299,602 views 5:15 Why are there Air Bubbles in my Pool? Now I have no lights on or anything although the spa is getting power it will not come on at all. Whether you're draining and refilling in the middle of the season or filling up for the first time this winter, there's a good chance you're going to run into this problem. More How to release an air lock in your spa More Above Ground Pool Buyers Guide More HomeMeet PrecisionContact UsThe Blog978-388-2585 NavigationHomeInground PoolsPool ServiceHot TubsMeet PrecisionContact Us Recent Articles 8 http://www.troublefreepool.com/threads/9426-Jets-not-working-after-fresh-fill

Some Hot Tub Jets Not Working

It’s important to know when it’s necessary to call on a licensed repair-man, or when you can make a simple repair and save yourself a bundle. Janis Cuthbertson Thank you kathleen I have an aruba hot tub the error code is either 569 or sn9 not sure what this is but temp of hot tub is 115 If the pump is on low, it won't be a disaster, just a little wet. To proceed further for cleaning, remove the screws or bolts holding the impeller housing cover in place to expose the impeller.

If the plunger gets stuck on the hole, turn the spa off and remove it. scott May 15, 2016 Reply Hello, I have bubbles, I have water coming out the jets. Wondering what your spa is trying to tell you? Hot Tub Jets Weak What could be the problem and how do I fix it?

OH = Over heat. Half Of Hot Tub Jets Not Working Breaker is on gfci which isn't in line with hot tub is reset so I'm clueless to what the problem could be. Don't take the nut all the way off, just loosen it up and let a little water bleed out. Why?

I noticed that the pressure of my jets decreased tremendously after draining and refilling as well as not heating the water efficiently either. In Ground Spa Jets Not Working Air switch buttons are often used on older spas, and you may have a problem with the switch or the hose. but no power to the top control panel display. If the filter just sits in a well behind a hole in the wall your life is much easier.

Half Of Hot Tub Jets Not Working

softcellelectrical 116,419 views 9:12 testing and replacing or servicing a hot tub or pool recirculating pump - Duration: 8:06.

I replaced the 20 amp slow burn fuse and Viola! Some Hot Tub Jets Not Working I was able to find my Union nut and burp my spa successfully! Hot Tub Air Lock Symptoms With a little luck, the next thing you hear will be bubbles coming from your jets followed by a fully primed pump.

it turns on 11/9/2016 11/9/2016 billyjr1961 I have a inground salt water pool 18,000 gallon. THANKS in advance! To check your impeller, shut off power and close valves on both sides of the pump. Can't access the equipment? Hot Tub Jets Won't Turn On

  • Third, Check that input voltage is correct, either 110V or 220V, +/- 10%.
  • Doing this will give you full access to the forums, where you will be able to receive personalized advice concerning your pool.
  • If not, you may have to use the drain plug or keep reading.
  • when you press Jet1 there is a brief sound as if it is trying to start.
  • If it does it sounds like the flo switch relay on the pc board is bad and may need a new pc board as you have changed everything else.Try running it
  • If you have a bleed screw on top of your filter, be sure to bleed air from there too.
  • Amesbury, Massachusetts 01913 Phone: 978-388-2585 Spring Hours: Saturdays: 9am-3pm Sundays: Closedinfo@precisionpool.net Massachusetts In-ground Pool Design, Construction, and Service.

The only other solution is removing the access panel and loosening the union nut on top of that pump and the air will leak out and the pump will begin pumping.Customer It has high and low speed. DO NOT DISCONNECT IT COMPLETELY. Check This Out Won't light up won't turn on won't do anything.

Watch Queue Queue __count__/__total__ Find out whyClose How To Fix the Air Lock on Your Hot Tub Pump | Arctic Spas HotTubsByArcticSpas SubscribeSubscribedUnsubscribe795795 Loading... Bathtub Jets Not Working Is the Jet Adjustable? please advise Jason Keller Vita spa 2006 model with l50 topside control.

There are a number of other possible causes to this problem.

Attached Images air relief.JPG (25.2 KB, 1085 views) Reply With Quote 10-14-2008,10:05 AM #2 meatloaf View Profile View Forum Posts View Articles Join Date Feb 2008 Location Gilbert AZ Posts It will not filter the water, doesn't look good to guests, and will probably stop you from putting the cover on properly. Water and electricity do not mix and carry the risk of electrical shock. Hot Tub Pump Not Working We emptied the tub to clean it and it restarted fine after it was refilled.

Clogged Drain Cover? Sign in Statistics 110,286 views 51 Like this video? That's your cue to start tightening. this contact form Janis Cuthbertson first I cleaned the filters then I replaced them still says flo Matt Giovanisci You may need to call a professional to take a look at your pump.

Third, something could be clogging up the pump impeller, especially if a spa cover is not used, and lots of small debris has entered the hot tub. The heat light is off and the thermostat is set lower than the water temperature. We tried unscrewing the screw on top of the filter and turning on drain valve which has no pressure by the way. Ask poolguy810 Your Own Question poolguy810, owner - pool and spa service company Category: Pool and Spa Satisfied Customers: 1671 Experience: Servicing pools and all brands of spas for over 28

Your spa heater won't work if your water flow rate is very low, so if your heater is working, chances are your filter is pretty clean. You must be logged in to post a comment. If you don't have drain plugs, you can slowly loosen the union on the pump (but don't remove it, or the o-ring may pop out of place). Usually it's the pump union in front of the pump that is loose, or the o-ring inside is out of position.

A hand made sheer decent waterfeature. Home Pool School Forum FAQ Forum Actions Mark Forums Read Quick Links View Site Leaders PoolMath Rules What's New? But it's definitely getting worse. With a little luck, the next thing you hear will be bubbles coming from your jets followed by a fully primed pump.

Just remember to open them again before you turn the spa back on. Danny Smith Just rebuilt pump and new motor, now the motor keeps kicking out when I turn on jets. Insect or ant infestation could also prevent the switch from operating correctly. Ralph Sampson This is not a good site for information.

Sign in to add this video to a playlist. The pump sounds fine, but there's no water moving.